重慶川儀4973電導池采用PES塑料作池體材料，抗腐蝕性強，可承受壓力1.72MPa，溫度140℃。電極材料有欽和石墨兩種。可采用插入式、流通式等安裝方式。4973,4973-001-333,4973-01-305,4973-10-333,4973-10-305,04973-X10-333-20
Chongqing
Chuanyi 4973 Series Conductivity Cells
are made of PES plastic which is of anti-corrosion and can bear the pressure of
1.72MPa as well as the high temperature of140℃. The electrode is made of Ti or
graphite. Insertion mounting and flow through mounting are selectable.
重慶川儀4973電導池的主要特點如下：
1.傳感器構造堅固，連續測量可靠，溫度*高至140℃,壓力*高至1.72MPa0
2.電導池有很強的抗腐蝕能力，電極為欽材料(電極常數為0.01和0.1電導池)或高密度碳材料(電極常數為1.0和10.0電導池)。
3.可插入式和流通式安裝，3/4"N尸下陽螺紋允許電導池**安裝在管道或罐上;電導池也用作實驗室浸入型用于批量采樣。
4.對于流通式應用，電導池能直接安裝在過程流體中，或用一個需單獨訂貨的3/4"管道丁型頭安裝在旁路流中，電導池已設計成保持電極和溫度補償器插在過程流中，保證電導池對溶液和溫度的變化作出快速和正確的反應。
5.對于衛生型clean-in-place(CIP)管線系統，4973探頭包括標準的3/2"或2"CIP連接件，適用于食品和飲料制藥和化妝品，或生物技術工業。
Main Technical Features
1.The sensor is firm in
structure and thus can work continuously The highest temperature It can bear is140℃, and highest pressure 1.72MPa
2.This series舊of great anti-corrosion capacity
for the electrode is made of Ti (of which electrode constant is 0.01 and
conductivity cell 0.1) or graphite of high density (of which electrode constant
Is 1.0 and conductivity cell 10.0)
3.Suitable
for either insertion mounting or flow through mounting Conductivity cell can be
fixed on tube permanently by 3/4 NPT male screw thread.
4.For the flow through
mounting, conductivity cell can be installed In the fluid directly or be
assembled near the bypass flow. The conductivity cell has been designed to be
sensitive enough to the variation of solution and temperature
5.For the clean-in一place (CIP) tube system, 4973
consists of standard 3/2" or 2" CIP connector, and can be used in
food industry, beverage production, cosmetic production as well as
biotechnology industry
使用維護
.4973電導池維護量極小，只有當沉渣累積在電導池中，影響電導池的工作性能時，則需對電導池進行清洗。
.清洗一般采用無機酸，不僅快速、高效，并且十分充分;另一種方法采用高壓水流沖掉附著的雜質，再用自來水和蒸餾水徹底清洗。
.電導池外殼由聚苯醚材料制成，所以禁止用丙酮、氯仿、甲苯或氯烴等試劑清洗。
.當測量值小于0.5 a s/cm電導率時，取樣化驗的值與在線表不具可比性，建議采用取樣杯從在線表出口取樣溢流進行實時測量比較，這樣可以大大降低空氣對水質的誤差影響。
.Application and
Maintenance
.4973 series conductivity
cells require minimal maintenance. Only when the waster accumulated on the
cells affecting work performance, the cleaning is required.
.Generally, nonorganic acid
is used when cleaning, which is efficient and fast in response. High pressure
water stream can be used to wash out the deposit after which tap water or
distilled water is applied to make a final clean.
.For the conductivity cell is made of phenylene oxide, none of
acetone, chloroform toluene or chlorohydrocarbon can be used as cleanser.
.When conductivity is no
more than 0.5 N s/cm, real time measurement is much more reliable for it can
lower the influence of air on water quality
咨詢電話：
- 溫馨提示：為規避購買風險，建議您在購買前務必確認供應商資質與產品質量。
- 免責申明：以上內容為注冊會員自行發布，若信息的真實性、合法性存在爭議，平臺將會監督協助處理，歡迎舉報